10 Meetups On Nissan Qashqai Key Fob You Should Attend

Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai has a distinctly SUV-like feel due to its larger dimensions. Moreover, the wheel sizes of 19 inches in Ti and ST-L models may be a bit spongy at times. The front tyres of Qashqai can also lose traction on rough surfaces, and the CVT may occasionally display a wrist-flexing torque steering.

This is usually due to an inoperable coin battery, which can be easily replaced in a matter of minutes. Make sure that the replacement battery is of the same voltage, size and specifications.

Water Damage

Water damage is among the most common causes that cause a Nissan keyfob to display the "key ID wrong" message. The key fob comes with rubber seals that shield the electronic chip inside. However, prolonged exposure to moisture can cause it to cease functioning properly. It's typical to observe this if your keyfob has been dropped into the ocean or in a pool. However, it could also happen when it gets wet from rain or soapy hands.

If your key fob was exposed to water over an extended period of time, you may need to clean it using isopropyl or electronic cleaner. Or, it could require taking to an expert to repair or replace it.

If your key fob does need to be replaced, the procedure is relatively simple. Make sure you have the correct multipack (CR2032 3V). Then open the front and back cases with the small flathead screwdriver. Remove the metal clips, then remove the battery, and then replace it. Reassemble the fob and replace the mechanical key. Check to see if it functions properly. If it isn't it, you'll need to bring it to a Nissan dealer or a professional auto locksmith to replace the key chip. Fortunately, the chip is not typically damaged by exposure to water and this shouldn't be too expensive.

Dead Coin Battery

The coin battery is another common reason that your Nissan Qashqai remote key fob might not work. The batteries last for about 3 to 5 years, but they are prone to failure over time when the fob is frequentedly dropped. You could replace the battery but make sure it is the same voltage and same size as the original. If you install a new battery, it could cause the key to be assigned an incorrect key ID. This will stop it from being linked to your vehicle.

The most efficient method of replacing the coin battery on the Nissan Qashqai key fob is by opening the key fob using an small screwdriver that has a flat head. The screwdriver should be put into a small notch at the bottom of the key fob. Simply twist the screwdriver to divide the two halves. Remove the old CR2025 battery and replace it with a new one, making note of the position of the old one within the fob.

Before putting the new battery in place check to ensure there is no dirt or water damage to the terminals. If there is, wash the terminals with a small amount of isopropyl alcohol. You'll also want to ensure that the pole cables are connected correctly - they should be connected to the positive and negative poles of your battery, respectively.

nissan keys

If your Nissan Qashqai key fob stops working after exposure to pure rain or tap water it could be an indication of a chip issue inside. You'll need a new keyfob in the event that you can't solve the issue by replacing the battery. If the key fob didn't work after dropping it, it is likely that the chip inside was damaged. You can usually get the key fob to function again if you take it out and clean the chip using alcohol and paper towels and then put it back in.

A common error that you may notice on your car's dashboard is "Key ID Not Correct." The vehicle is unable recognize the key fob, which is why it won't allow the car to start. The issue can be caused by a variety of things including water damage, undetectable problems in the key fob's circuitry or RFID interference.

The key fob will cease to function if the 12 volt batteries are dead or do not provide enough electrical current. This can affect the remote keyless system as well as central locking on your Nissan Qashqai, as well as stopping you from starting the engine using the key fob (if equipped with Intelligent Key). Examine the batteries on the key fob in case you are not able to lock or unlock your door by hand. Try re-inserting the battery to reset the transmitter.

Reprogramming

If the key fob was not submerged in saltwater it should be restored to its original state with a simple wash of clean water. You could also try cleaning the electronic chip using isopropyl Alcohol or an electronic cleaner. If none of these work then it might be time to replace the entire key fob by a new one.

If your Nissan Intelligent Key is still not working, there could be an issue with the connection between it and your car. Start by turning the ignition switch without activating the vehicle. Continue doing this until the hazard lights flash twice. Turn off the vehicle and remove the key.

Open the fob compartment in your vehicle's fob compartment. It's usually found on a door jamb or driver's door handle. Find the small "program" button and press it. After the program is complete, you should hear an emitted sound.

Now that your Intelligent Key is relinked to the car It's time to test it out. Press all the buttons on the key while standing a distance away from the car. If the lights flash, or the horn sounds, then the key is successfully connected to the Nissan. You can also test it near the Nissan.